| MPD.CONF(5) | Music Player Daemon | MPD.CONF(5) |
mpd.conf - mpd.conf documentation
mpd.conf is the configuration file for mpd(1).
Usually, that is /etc/mpd.conf, unless a different path is specified on the command line.
If you run MPD as a user daemon (and not as a system daemon), the configuration is read from $XDG_CONFIG_HOME/mpd/mpd.conf (usually ~/.config/mpd/mpd.conf). On Android, mpd.conf will be loaded from the top-level directory of the data partition.
Each line in the configuration file contains a setting name and its value, e.g.:
connection_timeout "5"
Lines starting with # are treated as comments and ignored.
For settings that specify a file system path, the tilde (~) is expanded to $HOME. In addition, the following path expansions are supported:
Example:
music_directory "~/Music" db_file "$XDG_CONFIG_HOME/mpd/database"
Some of the settings are grouped in blocks with curly braces, e.g. per-plugin settings:
audio_output {
type "alsa"
name "My ALSA output"
device "iec958:CARD=Intel,DEV=0"
mixer_control "PCM"
}
The include directive can be used to include settings from another file; the given file name is relative to the current file:
include "other.conf"
You can use include_optional instead if you want the included file to be optional; the directive will be ignored if the file does not exist:
include_optional "may_not_exist.conf"
See docs/mpdconf.example in the source tarball for an example configuration file.
This manual is not complete, it lists only the most important options. Please read the MPD user manual for a complete configuration guide: <http://www.musicpd.org/doc/user/>
This specifies the user that MPD will run as, if set. MPD should never run as root, and you may use this option to make MPD change its user id after initialization. Do not use this option if you start MPD as an unprivileged user.
Change to this group. This discards all default groups and uses only this group. Do not use this setting.
This specifies the file to save mpd's process ID in.
This specifies where the log file should be located. The special value "syslog" makes MPD use the local syslog daemon.
Suppress all messages below the given threshold. The following log levels are available:
This specifies where the db file will be stored.
The location of the sticker database. This is a database which manages dynamic information attached to songs.
This specifies the directory where music is located. If you do not configure this, you can only play streams.
This specifies the directory where saved playlists are stored (flat, no subdirectories). If you do not configure this, you cannot save playlists.
This specifies if a state file is used and where it is located. The state of mpd will be saved to this file when mpd is terminated by a TERM signal or by the kill command. When mpd is restarted, it will read the state file and restore the state of mpd (including the playlist).
Control if MPD will follow symbolic links pointing outside the music dir. You must recreate the database after changing this option.
Control if MPD will follow symbolic links pointing inside the music dir, potentially adding duplicates to the database. You must recreate the database after changing this option.
This specifies the whether to support automatic update of music database when files are changed in music_directory. (Only implemented on Linux.)
Limit the depth of the directories being watched, 0 means only watch the music directory itself.
This specifies whether relative or absolute paths for song filenames are used when saving playlists.
This specifies the character set used for the filesystem. A list of supported character sets can be obtained by running "iconv -l". The default is determined from the locale when the db was originally created.
Put MPD into pause mode instead of starting playback after startup.
If yes, and MPD has been compiled with support for Avahi or Bonjour, service information will be published with Zeroconf.
If Zeroconf is enabled, this is the service name to publish. This name should be unique to your local network, but name collisions will be properly dealt with. %h will be replaced with the hostname of the machine running MPD.
Specifies how replay gain is applied. software uses an internal software volume control. mixer uses the configured (hardware) mixer control. none disables replay gain on this audio output.
Specifies which mixer should be used for this audio output: the hardware mixer (available for ALSA, OSS and PulseAudio), the software mixer or no mixer (none).
mpd(1), mpc(1)
Max Kellermann
2003-2025 The Music Player Daemon Project
| July 11, 2026 | 0.24.13 |